Ford’s 335-series V-8, commonly known as the Cleveland, arrived for 1970 with some of the most ambitious cylinder heads ever fitted to an American production V-8. Its canted valves, broad intake ports and compact combustion chambers promised the breathing of a racing engine in a package sized for intermediate and pony cars.
The name requires explanation. 335 was Ford’s internal designation for the engine family; Cleveland identified the Ohio engine plant that built the American 351-cubic-inch version. Neither term describes just one engine. The family included the U.S. 351 Cleveland, the taller-deck 400 and 351M, and Australian 302- and 351-cubic-inch versions that remained in production after American 351C manufacture ended.
The Cleveland’s reputation rests especially upon its cylinder heads. The large-port 4V version could support extraordinary high-speed airflow, while the smaller-port 2V head produced better mixture velocity for ordinary driving. That choice created both the engine’s versatility and its enduring controversy. A properly matched Cleveland could be exceptionally strong; an engine assembled from impressive but poorly matched parts could be disappointing below the top of the tachometer.
Why Ford needed another 351
Ford already had the 351 Windsor when the Cleveland appeared. Introduced for 1969, the Windsor enlarged the familiar small-block Ford architecture with a taller deck and longer stroke. It was compact, proven and well suited to everyday passenger cars.
The Cleveland pursued a different objective. Ford wanted greater breathing potential for performance and anticipated increasingly stringent emissions requirements. The new engine retained the Windsor family’s 4.38-inch bore spacing and the 351’s 4.00-inch bore and 3.50-inch stroke, but almost every major casting was different.
The 351C block incorporated its timing-chain housing rather than using the Windsor’s separate aluminium front cover. Coolant routing differed: Cleveland heads returned coolant through their deck faces into the block instead of through the intake manifold. The Cleveland used smaller 2.75-inch main-bearing journals, compared with the 351W’s 3.00-inch journals, and its intake manifold, oil pan, timing components and exhaust pattern were unique.
Consequently, identical displacement does not imply interchangeability. “351” identifies cubic inches; the suffix identifies the engine family.
| Feature | 351 Windsor | 351 Cleveland |
|---|---|---|
| U.S. introduction | 1969 | 1970 |
| Bore × stroke | 4.00 × 3.50 in. | 4.00 × 3.50 in. |
| Bore spacing | 4.38 in. | 4.38 in. |
| Main-journal diameter | 3.00 in. | 2.75 in. |
| Cylinder-head layout | Inline valves | Canted valves |
| Timing cover | Separate aluminium cover | Cast into block |
| Coolant exit | Through intake face/manifold | Through head deck into block |
Poly-angle valves and two very different heads
The Cleveland’s defining feature was its poly-angle cylinder head. Intake and exhaust valves were canted in two planes instead of standing in a single line. This arrangement allowed large valves, reduced shrouding by the cylinder wall and gave the ports a more direct approach to the chamber. The concept had been proven in Ford’s experimental and racing programmes and appeared in related form on the Boss 302 before the production 351C.
Ford offered two principal port sizes. The terminology referred originally to carburetor barrels, but it came to identify complete induction packages.
The 2V head used smaller intake and exhaust ports and smaller valves. “Small” is relative: its passages were still generous for 351 cubic inches. Higher mixture velocity improved throttle response and low-to-medium-speed torque, making the 2V appropriate for heavy cars, automatic transmissions and ordinary axle ratios. Most used open combustion chambers.
The 4V head used enormous ports and 2.19-inch intake valves. Early versions combined those ports with closed, or quench, chambers. Near top dead centre, flat areas of the piston approached matching areas of the head and forced mixture toward the active chamber. With suitable pistons and clearances, this promoted turbulence and resistance to detonation.
At high engine speed, the 4V head flowed exceptionally well. At low speed, its great port volume could reduce mixture velocity. The engine might feel soft until rpm rose far enough to use the available area. This was not evidence that the head was bad; it showed that port size, camshaft, compression, intake, gearing and vehicle weight had to be treated as a system.
The 1970 engines
For 1970, the 351 Cleveland appeared in both 2V and 4V form. Representative advertised gross horsepower was approximately 250 for the two-barrel engine and 300 for the four-barrel version, although ratings and equipment varied by car line and market.
The 2V was the broad-use engine. Its two-barrel carburetor, hydraulic camshaft, smaller ports and open chambers emphasized tractability. The 4V added a four-barrel carburetor, higher compression, larger valves and the famous closed-chamber heads. Mustangs and Torinos gave the Cleveland its most visible American applications, while Mercury used it in corresponding Cougar and intermediate models.
The engine also crossed the Atlantic. De Tomaso selected the 351C for the mid-engined Pantera, introduced for 1971 and sold for several years through Lincoln-Mercury dealers in the United States. The Pantera associated the Cleveland with an exotic body and European chassis, even though its engine remained recognizably American in construction and character.
Boss 351: the Cleveland at its sharpest
The 1971 Boss 351 Mustang contained the most celebrated factory version. Its block used four-bolt main caps on the centre three journals. The 4V closed-chamber heads were modified for screw-in studs, guideplates and an adjustable valvetrain. A mechanical-lifter camshaft, forged pistons, aluminium intake manifold, four-barrel carburetor and free-flowing exhaust completed the package.
Ford rated the Boss 351 at 330 gross horsepower and 370 pound-feet. Period testing showed that the rating did not exaggerate its performance. The engine combined the Cleveland head’s high-speed breathing with enough compression, camshaft and gearing to make the combination work as intended.
The Boss name disappeared after one year. For 1972, a related engine became the 351 High Output. Lower compression, open-chamber heads and the industry’s change from gross to SAE net ratings make direct comparison difficult. The 351 HO was rated at 275 net horsepower—still formidable in a year when advertised outputs fell dramatically.
Cobra Jet and the spread of open chambers
The 351 Cobra Jet joined the range during 1971. It combined 4V-style ports with a hydraulic camshaft, spread-bore four-barrel carburetion and a more street-oriented specification than the Boss. Four-bolt main caps appeared on CJ blocks, although Ford casting and machining variations require verification rather than assumption during a modern rebuild.
For 1972, Ford increasingly used open-chamber 4V heads. Lower compression helped engines tolerate lower-octane unleaded fuel and comply with emissions requirements, but the very large chamber could be detonation-prone if a modern builder simply raised compression with a domed piston. Contemporary Cleveland builds often prefer a smaller modern chamber and a flat-top piston, preserving quench rather than recreating an open-chamber high-compression combination.
By 1973 and 1974, American 351C output and compression had declined. The Q-code four-barrel remained the principal performance version, but heavier cars, milder camshafts and emissions equipment changed its character. U.S. production of the 351 Cleveland ended after 1974.
The taller-deck 400 and 351M
The 335 family did not end with the 351C. Ford introduced the 400 for 1971. It retained the Cleveland’s 4.00-inch bore but used a 4.00-inch stroke and a block approximately 1.1 inches taller. The extra deck height accommodated the longer stroke and connecting rods. Main bearings grew larger, and the block used the 429/460 bellhousing pattern.
The 400 was designed for torque in large passenger cars and trucks, not as a high-rpm successor to the Boss 351. Most versions used 2V-style heads, modest compression and conservative camshaft timing. Its nearly square dimensions delivered useful low-speed output, but emissions-era calibrations and heavy applications gave it an undeserved reputation as merely a smog engine.
The 351M appeared for 1975. It combined the 400’s tall block and 4.00-inch bore with a 3.50-inch stroke. The “M” is commonly expanded as Modified, although Ford’s period usage was not always consistent. Mechanically, the crucial point is that the 351M belongs with the 400, not with the low-deck 351C or the Windsor.
| Version | Bore | Stroke | Deck family | Principal character |
|---|---|---|---|---|
| 351C | 4.00 in. | 3.50 in. | Low deck | Passenger-car and performance engine |
| 400 | 4.00 in. | 4.00 in. | Tall deck | Large-car and truck torque |
| 351M | 4.00 in. | 3.50 in. | Tall deck | Truck and full-sized-car service |
Australia keeps the Cleveland alive
Ford Australia gave the Cleveland a longer and more varied life. Local production at Geelong began in the early 1970s and continued into 1982. Australian Falcons, Fairlanes, LTDs and performance models used both 351- and 302-cubic-inch versions.
The Australian 302 Cleveland combined the 4.00-inch Cleveland-family bore spacing with a 3.00-inch stroke. Its locally developed heads used smaller ports and compact closed chambers, a combination later valued by performance builders because it provided better velocity and useful quench without the huge passages of the American 4V head.
Australian 351s became central to Falcon performance history, including GT and racing applications. Local touring-car competition demonstrated that the basic architecture remained capable long after emissions and fuel economy had ended the American 351C’s short production run.
Racing and the Cleveland legacy
The Cleveland’s influence extends beyond engines carrying a 351C label. Canted-valve Cleveland-style heads helped the Boss 302 compete in Trans-Am racing. The production 351C and its derivatives appeared in drag racing, stock-car competition, Australian touring cars, offshore powerboats and countless modified street cars.
Its architecture also inspired hybrids. The best known is the “Clevor”: Cleveland-style heads on a Windsor-family block. Because the families route coolant differently, the conversion requires appropriate passages, intake manifold and other details; the heads do not simply bolt on to create a finished engine. Modern aftermarket blocks and heads have blurred the old boundaries further, combining Windsor bottom-end convenience with Cleveland breathing principles.
The engine rewards careful specification. Traditional 4V heads suit high rpm and substantial displacement, but may be excessive for a mild 351 in a heavy street car. The 2V head, Australian closed-chamber casting and modern aftermarket heads often produce a broader torque curve. Oil control, valvetrain geometry, piston-to-valve clearance, compression and ignition timing all deserve attention. A famous casting number cannot substitute for a coherent combination.
Why the 335 Cleveland mattered
The Ford 335 Cleveland V-8 arrived at an unfortunate moment. Its best versions appeared just as insurance pressure, emissions regulations, lower compression and changing fuel quality ended the first muscle-car era. American 351C production lasted only five model years, far less than the Windsor family it briefly supplemented.
Yet its engineering was forward-looking. The canted-valve heads separated port design from the restrictions of an inline valvetrain and offered airflow far beyond what most street engines could use in 1970. The 2V and 4V versions showed two legitimate approaches to the same problem: mixture velocity for ordinary operation and maximum area for high-speed power.
The Cleveland’s enduring lesson is not that bigger ports are always better. It is that airflow must be matched to displacement, engine speed and purpose. Ford created a family capable of powering luxury cars, trucks, Mustangs, an Italian exotic, and Australian racing Falcons. Few engines better illustrate both the possibilities of ambitious cylinder-head design and the importance of treating an engine as a complete system.
Sources and further reading
- Ford Motor Company. (1970–1974). Ford and Mercury shop manuals, sales literature, and engine specifications. Ford Heritage Vault. https://fordheritagevault.com/
- Ford Racing Performance Parts. Ford Racing Performance Parts catalog: Engine history and identification. https://performanceparts.ford.com/download/pdfs/EngineHistory.pdf
- Ford Motor Company. 50 years of Mustang milestones. https://media.ford.com/content/dam/fordmedia/North%20America/US/2013/12/05/Mustang_Milestones.pdf
- Hammill, D. (2006). How to build and modify Ford 351 Cleveland and 351/400M engines. Veloce Publishing.
- McLaughlin, G. R. (2015). The complete book of Ford Mustang: Every model since 1964½. Motorbooks.
Specification note: Ford changed compression ratios, camshafts, carburetion, heads and advertised output by model, market and year. Pre-1972 gross horsepower ratings are not directly comparable with later SAE net figures.